![]()
The streaming pauses are just on the iPad and also on the iPhone. I'm going to try changing the scaled size to 240x20 with an offset of 0x524, to see if that reduces the overall data rate and wards off streaming pauses. The offset of the subtitles is given as 0x462 pixels, and 462 + 81 is 543, near enough to 544. Subler says the subtitle track's visual settings use a normal size and also a scaled size of 960x81 pixels, in a file whose video resolution is 960x544. srt file into a "Tx3g" track in its output file. srt file containing kmttg-derived closed captions. That subtitles track was created by the Subler remux utility, based on a. It looks like the data rate for the subtitles track itself is huge! Much greater than the data rate for the video track. But with subtitles on, those counts started shooting up by the tens of millions every few seconds. With subtitles off, the count of bytes being sent and received on the appropriate network connections edged up at a reasonable rate, in the tens of thousands every few seconds. So I looked at my router's traffic monitoring stats in Safari on my iPhone while the video was being streamed to my iPad. Yet it still gives me streaming pauses when soft subs are on. This newer, "LBR" version has such a low bitrate that it exhibits macroblocking when played. I made a very, very low bitrate version of the file alluded to above that streams fine until soft subs are turned on, but that tolerates soft subs in its earlier version that (I think) HandBrake made. #Subler hangs opening m4v how to#Of course, this does not tell me what the maximum bitrate is, so these things are quite hard to pin down.Īny help that anyone can give me insofar as how to further diagnose this problem and eventually triumph over it will be much appreciated. The video that does not pause has a slightly higher data rate, according to QuickTime Player, than the one that pauses: 2.44 Mbits/s vs. I realize this could be an issue involving too high an average bitrate or too high a maximum bitrate, but it looks like it's not that simple. But remaking it using the workflow I just described has given me a video with unwanted streaming pauses. When I stream it while displaying soft subs, no pauses. #Subler hangs opening m4v mp4#mp4 and incorporate captions as soft subtitles. I have one video that I made some time ago using, if I remember correctly, HandBrake to both transcode. As I say, the play of the stream typically gets interrupted by unwanted pauses, but only when I tell the Videos app to show the soft subtitles. I can stream that file to my iPad's Videos app via its Sharing capability. m4v file that I add to my iTunes library. I use a Mac utility called Subler for that. srt file, the one containing the closed captions that kmttg created. ![]() mp4 file, using an appropriate profile whose parameters (resolution, average bitrate, max bitrate, etc.) I have tried to adjust to get rid of the problem, with no success yet. mpg file (in case I need it later) and then I also save it as a. #Subler hangs opening m4v tv#After using kmttg to download, decrypt, and extract captions from a TV show, I use VideoReDo to manually do a QuickStream Fix and trim off the video's unwanted material. I can't be sure where the bottleneck is located. So the act of turning on subtitles seems to bottleneck the stream at some point. If I turn off the subtitles, I can watch the video pause-free. ![]() It looks as if the scrubber bar has run out of buffered material at each pause point. When I turn on the subtitles track while watching a video as it is streamed to the iPad, I get irritating pauses. ![]() The videos, by design, wind up with closed captions in the form of soft subtitles. I need help with a problematic workflow that begins with kmttg and ends with Home Sharing videos from iTunes to my iPad. It seems to work best using "java downloads" mode, not curl, and you cannot enable "Use RPC to get NPL when possible" option if you want to use it, since RPC data doesn't have the byte offset needed for resume.Īpologies if this is not the right thread/forum. #Subler hangs opening m4v code#Resume downloads is somewhat flaky but working with 20.4.1 and has been re-enabled in source code in preparation for next release. So you're comparing apples and oranges.Īs I said, you can test multiple downloads at once pretty easily by starting 2 or more kmttg windows and downloading 1 show in each. ![]() The iOS streaming uses MRS to get stream from the TiVo, and then Stream hardware to transcode to H.264, so it's MRS based as well. 2 or more MRS streams at once have been possible ever since MRS first came out. #Subler hangs opening m4v series#TTG has a lot more work to do as it involves decrypt, demux, remux, encrypt, a process which historically has consumed a lot of CPU cycles which is why it is faster with each TiVo series getting a better CPU. Multi Room Streaming (MRS) is different than TiVo To Go (TTG) in that it is just transferring bits. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |